---

Click on a Hex Head Cap Screw type above to continue shopping...

Hex Head Cap Screws

Hex head cap screws are headed fasteners with external machine threads. They are used to fasten two or more parts together and allow for maintenance and repair disassembly.

Having either cut or rolled screw threads that comply with the Unified system—UNC (Unified National Coarse) and UNF (Unified National Fine)—right-hand threads are standard so turn clockwise to tighten. Short hex head cap screws are fully threaded while longer lengths follow a standard formula: for screws 6" and shorter, the threaded length is two times the basic thread diameter plus 1/4", and for lengths greater than 6", two times the diameter plus 1/2". This, however, is the minimum threaded length and manufacturers may thread the screw substantially more. In addition, some longer screws are fully threaded and are often called tap bolts. The point of hex head cap screws is chamfered or rounded to protect the first thread from damage and to facilitate entry into an internally threaded part such as a tapped hole or nut.

Ranging in size (diameter) from 1/4" to 1 1/2", 1/4" to 1 1/4" sizes are common. Lengths range from 3/8" to 24"; 1/2" to 10" is typical. Larger sizes are not manufactured in short lengths, just as smaller sizes are not available in long lengths. Size and length are specified in fractional inches; length is measured from the underhead washer bearing surface to the extreme point (threaded end) of the screw.

Hex head cap screws have hex (short for "hexagon") heads along with an underhead washer bearing surface. The size of the head varies with the size of the screw.

Steel hex head cap screws are available in different strength "grades" as designated by the SAE (Society of Automotive Engineers): Grade 2, 5 and 8. Another option is Grade 9, which is generally accepted to be about 20% stronger than SAE Grade 8. However, Grade 9 is not an SAE grade nor are its chemical and physical properties standardized.

Common materials are steel (unplated and plated), stainless steel, brass, silicon bronze, and nylon. Unplated or uncoated steel, referred to as "plain finish," has not been surface treated to prevent rust other than a light coating of oil for temporary protection. Consequently, common finishes for steel are zinc plating and hot dip galvanizing.

Hot dip galvanized, stainless steel and silicon bronze are usually recommended if the hex head cap screws will be used with pressure preservative treated wood such as "ACQ" (Alkaline Copper Quaternary)—check local building codes and contact your lumber supplier for recommendations. In marine environments, stainless steel may show signs of severe pitting corrosion when submerged in salt water that lacks free oxygen, which makes silicon bronze a preferred material because stainless steel needs oxygen to create its self-healing, corrosion-resisting chromium oxide film.

Unlike other types of fasteners, which mainly come from offshore manufacturers, you have a choice with Grade 5 and 8 hex head cap screws: imported (often from Asia), Canada and domestic (USA). Imported fasteners tend to be the least expensive, Canada is priced a little higher, and domestic may be the most expensive (the number of dollar signs [$] indicate relative price).

When selecting a nut for use with a graded hex head cap screw, it is very important that the nut be the same grade as the bolt; one grade higher is also acceptable as one source states. Grade 2 flat washers should only be used with Grade 2 cap screws—use hardened flat washers with Grade 5 and 8 hex head cap screws. Also, use only SAE pattern flat washers with Grade 5 and 8 cap screws because, as it is explained, the oversized hole in USS washers is too large to properly support the bearing surface of the cap screw's head and one washer size smaller will be too tight and may cause the head to fail. As for lock washers, which are often split (helical spring) type, use regular for Grade 2 cap screws and high strength alloy steel for Grades 5 and 8.

Hex head cap screws are also called cap screws, hex cap screws, hex bolts, finished hex bolts, hex head bolts and, if fully threaded, tap bolts, hex tap bolts and hex head tap bolts.

Hex Head Cap Screws
Brass
Coarse Thread	Brass
Steel, Grade 2
Coarse Thread, Hot Dip Galvanized Coarse Thread, Plain Finish Coarse Thread, Zinc Plated Coarse Thread, Fully Threaded, Zinc Plated	Grade 2, Galvanized Grade 2
Steel, Grade 5
Coarse Thread, Plain Finish, USA/Canada Coarse Thread, Zinc Plated, Global ($) Coarse Thread, Zinc Plated, USA/Canada ($$) Coarse Thread, Zinc Plated, USA ($$$) Coarse Thread, Fully Threaded, Zinc Plated Fine Thread, Zinc Plated, USA/Canada ($$) Fine Thread, Zinc Plated, USA ($$$)	Grade 5, USA/Canada Grade 5, Global Grade 5, USA
Steel, Grade 8
Coarse Thread, Yellow Zinc Plated, USA/Canada ($) Coarse Thread, Yellow Zinc Plated, USA ($$) Fine Thread, Yellow Zinc Plated, USA/Canada ($) Fine Thread, Yellow Zinc Plated, USA ($$)	Grade 8, USA/Canada Grade 8, USA
Steel, Grade 9
Coarse Thread, Zinc Dichromate Plated, USA Fine Thread, Zinc Dichromate Plated, USA	Grade 9, USA
Nylon
Coarse Thread	Nylon
Silicon Bronze
Coarse Thread	Silicon Bronze
Stainless Steel
304 (18-8), Coarse Thread 304 (18-8), Fine Thread  316, Coarse Thread	Stainless Steel

FF:HXHDCPSCRW v1.1